Netduma Fraser

Improvements in terms of connection quality? Unlikely as generally it does increase your ping, there isn't a specific VPN we recommend. DMZ doesn't create any port forwarding rules so whatever that is you can delete it

It's region locked to the place of purchase, however, this may help you get it changed: https://community.netgear.com/t5/Orbi-Wi-Fi-5-AC-and-Orbi-with/Change-region/td-p/2025003

Added, enjoy! https://forum.netduma.com/forum/144-netduma-r2-early-access/

Added, enjoy! https://forum.netduma.com/forum/144-netduma-r2-early-access/

Here is another topic where someone had the exact same issue 2 years ago and this comment specifically explains why it may be a problem: So probably best to contact Netgear and see what they can do.

Yeah I mentioned it's an issue we're looking into, I'm referring to the YT/Netflix streams while gaming

Can you provide a screenshot of the Network Monitor when a stream and gaming is happening at the same time please?

Looks pretty good, may only need a slight tweak to get those small spikes out, try 65/65 and run the test again. Also when gaming try disabling Traffic Prioritization and see if that stops the stream buffering.

Ah yes, I think you'll need to try a few reboots, that's really the only thing that would resolve it - I assume you wouldn't want to do a factory reset for that

70% is a good starting point but it may not necessarily be the value that works best for you. Could you provide a screenshot of a completed Connection Benchmark test please?

No you don't need to worry about this

Not specifically no but go to the System Information page and then in the Rapp panel menu ≡ change the retries to 5, reboot from the interface, wait 2 minutes before accessing and see if it works then please.

Try the above for WiFi disconnects, it's most likely interference which those suggestions will help with. What do you usually have Congestion Control set to?

That's right, Normal for wired devices, Gaming/Voice for wireless devices. You can enable Apply to WAN, if your ISP supports priority tags you may notice an improvement, if not it's fine to keep enabled. Yes that's right.

Tray was correct but also devices such as phones have an option for Private/Random MAC addresses which would cause that behavior as it essentially makes the router see it as a new device everytime it connects. Give it a reboot, wait 2 minutes and it should load then

You can leave MTU at the default setting. Generally yes it would be good to keep UPnP enabled as other devices would rely on it but if you're not encountering any issues you could leave it disabled.

It's not specific to this beta I know that for certain, otherwise we would have had a lot more people experiencing it, however you will find on the Netgear site people who have experienced the same thing with other versions. For whatever reason an upgrade can sometimes trigger it to not work. As of yet I have seen no permanent fix for this and I have advised everyone who has experienced it in the past to contact Netgear about it. Given the XR700 is no longer made it's unlikely they would be able to provide a replacement if you were within the warranty period. As I mentioned WiFi isn't our domain so I will pass it on for a dev to have a look but I don't like the odds that they'll be able to do anything. They're also very busy so may not have a chance to look at it until next week.

That looks okay, I take it there aren't any other devices in the immediate vicinity? For the XR1000, change the mode on 5GHz from 4800Mbps to the next one down, I believe it's 2400Mbps and see if that works better please. Ah to reset then you would need to do so in Settings > Administration > Backup Settings > Erase

Could you make a new topic for your issue please and we'll be happy to help there. Include what you have tried so far as well please.

There are no 'best' settings that work for everyone, there are settings that we recommend you start with and then experiment from there. Yes you should do that for the Geo-Filter but set Ping Assist to 0. For QoS it's entirely up to you and what your network usage is like, if you want it to always apply as people are often streaming or downloading for example then always would be a good choice. If you only want it to apply when you're gaming then use auto enable. We suggest starting with 70% and going from there. You can use Connection Benchmark, specifically the Ping Under Load as an indicator of whether you need to fine tune Congestion Control - you want that graph to look as close to the Ping Test graph as possible.

As above it's a good service for games that aren't listed but overall yes it's to be used for Games Consoles so you would select that for the PS5. The page is out of date at the moment as the previous person who was in charge of updating it has left and it's not been assigned to someone yet. I'll update it as best I can.

Great thanks Tray! Just so everyone is aware Alex is really busy at the moment but he will get to your captures so do keep them coming!

If you disable Adblocker does IPTV load correctly? What's the issue you're having with bandwidth allocation exactly? For WiFi try this to see if it is more stable: Disable Mirror Mode, give 2.4/5GHz different names and apply - you'll want to connect to 5GHz specifically for speeds Use a WiFi analyzer to find the least congested channel and change to that Experiment with the widths to see what gives better results Ensure it's in an elevated position - not on a metal surface Ensure there aren't any electrical / wireless devices e.g headphones etc within close proximity ~3 feet if possible Set the antennae to this position _ | | _

Alex is really busy at the moment but it will be done, it's something I am reminding him off frequently. eFootball specifically hasn't been added but it was built using the Unreal Engine which is an option you can select or you can select the device specifically.

Alex is really busy at the moment but it will be done, it's something I am reminding him of frequently. eFootball specifically hasn't been added but it was built using the Unreal Engine which is an option you can select or you can select the device specifically.