Netduma Fraser

Okay great, lets ignore waveform then as we can't rely on that currently to report accurately. There is likely some settings that are restricting the speeds. You mentioned you had the issue after a factory reset, is there anything you changed right away upon getting into the interface or did you test right away?

Here is a guide: https://www.vodafone.co.uk/cs/groups/public/documents/contentdocuments/vfcon090499.pdf then put the R2 WAN IP in it. What do you mean it can't connect to the internet exactly? You don't need internet to access the interface

Great to hear that, thanks for the update!

How have you set the powerhub to ensure all traffic flows to the R3? E.g. R3 in its DMZ, modem/bridge mode Could you try WiFi just to see if you get the same issue?

When this happens are you going away at any point and the console goes into standby/instant on mode and then when you play again it stops working?

Put your PC in the DMZ on the R3 then run speedtest.net what do you get? Remove the PC from the DMZ immediately once you've completed it

What is the M&K? Have you tried without the XIM? What firmware version are you on? Do you get the disconnects over WiFi?

That's a local IP address so likely another device you have connected, are you trying to matchmake against yourself/another device at home?

Good to hear, thanks for the update!

There is an article here that will help you: https://fttppro.co.uk/replacing-the-hub-5x-with-a-was-110-sfp-module-on-virgin-medias-xgs-pon-broadband/ I only skimmed it but it looks like you'd need a router with an SFP port to connect it to so in this case it wouldn't work with the DumaOS router. Presumably you could find an SFP > Ethernet adapter though and then it should work.

It does work, I'm just saying that sometimes it's unable to ping and that is expected. Try this: Quit the application/game/client completely Remove device from the Geo-Filter Give PC PlayStation Device Type in the Device Manager Resync from the Geo-Filter Map menu Re-add the device to the Geo-Filter with the manual option Set up the Geo-Filter how you like Wait 2 minutes Boot up application/game/client Then see if you see servers more consistently.

Thank you, that's all fine. You said it happened all of a sudden, can you think of anything that changed settings wise or with the physical setup e.g. adding a new device etc prior to the issue happening?

Try this: Quit the application/game/client completely Remove device from the Geo-Filter Give PC PlayStation Device Type in the Device Manager Resync from the Geo-Filter Map menu Re-add the device to the Geo-Filter with the manual option Set up the Geo-Filter how you like Wait 2 minutes Boot up application/game/client Then see if it works better.

Added, use the link above, the instructions to install are in the pinned topic at the top for the firmware

Added, the link will now work

Game servers don't respond to traditional pings so we try to be clever in order to get a successful ping but it doesn't always work. It will then try to fall back to the trace method which won't give you the correct ping in most cases but hopefully somewhere near it, however this can also fail. We're working on a new ping method that may help but I don't have an ETA for this. Are you using a PC?

Potentially if it's legally allowed but we are limited by that

Could you provide a screenshot of the full Geo-Filter page showing what you see when you get a game outside your radius please?

This is the chip used for the R3 WiFi: https://www.broadcom.com/products/wireless/wireless-lan-infrastructure/bcm6715

Added

You already have it https://forum.netduma.com/forum/151-netduma-r3-early-access/

Looks like a DHCP lease change, In Settings > DHCP > Add Rules > Select Device > Save. Do that for each device. Then in DHCP > Advanced change the lease time to 10000, save, reboot the router from the interface and see if it happens again please.

That's great to hear, thanks for the update!

The Nintendo should be under a console so when you add it to the Geo-Filter you don't need to select any games and can try to filter. We haven't specifically tested any Nintendo games that I know of and I'm not sure there are any plans to. Perhaps when the Switch 2 comes out there will be renewed interested and we can take a look further

Apparently WPS may not be working correctly again, we'll need to look into it. It should be possible yes though we haven't got specific support for mesh - if you check the manual for the repeater it should have an alternative way for you to connect it