Netduma Fraser

You don't need to set Bandwidth Allocation at all unless you have a specific requirement such as you're streaming and need consistent bandwidth as otherwise the bandwidth is just shared between devices based on what needs what. If you want to use it leave the XR1000 low/0 and all other devices can be allocated bandwidth.

Double check the IP on the console, does it match the IP of the device you think it is on the Device Manager? Did you add it to the Geo-Filter after the console/game was already on? If so that could be another reason, follow this process and see if it works: Quit the application/game/client completely Remove device from the Geo-Filter Give PC PlayStation Device Type in the Device Manager (if on PC) Resync from the Geo-Filter Map menu Re-add the device to the Geo-Filter with the manual option Set up the Geo-Filter how you like Wait 2 minutes Boot up application/game/client

Are you able to access it using the mobile web browser? Are you using iOS or Android and what firmware version is the phone using?

Hello, welcome to the forum! Were you previously receiving higher speeds? If so when did this start to occur, after changing settings, rebooting, resetting, upgrading etc. Yes that is the MicroTik hardware model.

Reset download Bandwidth Allocation, set each device for Apex to use 15% on Bandwidth Allocation for upload, then disable Share Excess on the Bandwidth Allocation menu and try again, see if that resolves it

No need to allocate bandwidth at all for your scenario but if you wish to then give bandwidth to the devices, you don't need to give any to the XR - it would just redistribute to the devices anyway.

I know it does have a problem with showing the ports so it may be having trouble opening as well but port forwarding is a good work around. In theory the bandwidth doesn't matter as the game uses so little, even if it shows 4k it will never use that much. Have you tried the R2 with the game since trying Early Access?

It's planned but nothing on it yet.

How do you have Traffic Prioritization set? Did it stop the issue you were having?

Copy the WAN IP of the XR from the System Information page then put that in the DMZ on the tenda and then see if it's better after that please.

May not be the router then, if you connect direct to your modem can you login?

What is the model of the ISP modem?

Give the R2 a reboot, wait 2 minutes then it should get internet.

Are one or both of you using the Geo-Filter at all when playing? What's the model of the modem/router the XR is connected to and how do you have that set up?

If you disable the Geo-Filter does that then allow you to login?

You'll need to add your friends to your allow list, you can see how to do this at the bottom of this guide, see if it works after that. https://support.netduma.com/en/support/solutions/articles/16000077072-dumaos-optimal-settings-guide-geo-filter

The APs may need a reboot as they'll be getting their IP from the R2 instead now and may not have switched to it on their own, see if that works.

It'll be a false reading if you have an Open NAT on the console but if you reboot the console does it then work again? The setting I got you to change increases the time that it applies the port so it won't stay that way all the time unless you really increase the value but that could cause some slow downs

I've asked the team to update it this week

Well done on resolving it and thanks for posting the solution, much appreciated!

I don't think we've tested the game specifically with the Geo-Filter yet but in theory yes. If you're using a PC set it to use a PlayStation device type in the Device Manager and add it to the Geo-Filter with the manual option and setup how you normally would and see if it works.

Which router is this for specifically? It's best to start with a high value for Congestion Control (set to Always), say 95% then do a test, decrease by 10%, test, decrease by 10% etc, until you get to a value that is pretty good and then try 5% either side of that value to see if it can be improved. It's important to note that Download & Upload on Congestion Control don't have to be the same value and that you may have a better experience with differing values.

No nothing to worry about!

Disabling Auto Ping is so you can manually ping the blocked icon on the map that should appear when getting kicked so you can then allow it which should then allow you into the game when you try again - it may take a few tries to allow the servers responsible for the kick.

Se eles estiverem usando servidores para bate-papo, você precisará permitir também, eles podem usar alguns, qualquer um que você encontrar, informe-nos o ID e podemos adicioná-los à lista de permissões