Netduma Fraser

They will show as wired yes for the reason you mentioned. I'm not sure if it's possible either as technically the AP is transparent to the router which is why the devices get the IPs from the R3, I will pass it on though. Did you rename them on the R3 or Orbi? If they have an IP it won't want to remove them so if you reboot the router that'll drop the IP and you can remove them then.

Try this, remove the console from the Geo-Filter and in the Device Manager change it to a PC then re-add it to the Geo-Filter, does it work better then?

We've never had anyone banned from using our routers/software in the almost 10 years we've been around so definitely what others have said

By not working, do you mean on the game you're not getting an open NAT or that port rules aren't shown on the page or both? Just responded to your topic

You don't have to do a factory reset and actually it's not really required anymore either. However, as there has been a few updates since the initial launch version (3 - 4) I feel that that is a good point to do a reset after another upgrade, just to clear out any potential remnants of previous versions that might cause issues. You can factory reset from the interface in Settings > Troubleshooting or as the other routers, hold the reset button in the back of the router for 30 seconds.

Try these steps and see if it works better: Disable GeoLatency Disable PingAssist (set it to 0,0) Enable Strict Mode Disable Fast Search Then restart game or wait 10 minutes (in the lobby in the game). If that doesn't work, reboot PC/Console and it should work then.

There are many servers clustered together in the same location so it'll be two different servers in the same location If a router is connected behind the R3 you'd have to be directly connected to it to access or if it has the ability, enable access from WAN As far as I know it's working correctly. Steady Ping affects your ping once you've got a game so you don't need to do any factoring

Thanks for the information, I will pass it onto the team to see if this helps in anyway, that's good about the link speed, does that actually convert into a higher speed test result?

What is the issue you're having exactly?

Interesting okay, so you should be getting max, thank you for the report, I will pass it onto the team.

Yes that is a good value to set

Thanks for that, it could be related to another issue we're looking at. In the meantime, try this, remove the console from the Geo-Filter and in the Device Manager change it to a PC then re-add it to the Geo-Filter, does it work better then?

Try this, remove the console from the Geo-Filter and in the Device Manager change it to a PC then re-add it to the Geo-Filter, does it work better then?

Try this, remove the console from the Geo-Filter and in the Device Manager change it to a PC then re-add it to the Geo-Filter, does it work better then?

È normale, non sarà sempre possibile eseguire il ping di un server

Los idiomas no son un error, es una característica y llevará tiempo traducir todo a diferentes idiomas. La VLAN funciona, es posible que no alcance 1 Gbps si tiene esas velocidades, pero está funcionando. Si el equipo puede aumentar esas velocidades, lo harán, pero es probable que primero se prioricen otras cuestiones: acaban de regresar de las vacaciones.

Yes that's right and if you do remove them they should come back I suspect once the devices start using traffic

Yes that's exactly right

Have a look at Ping Heatmap to find the ones around you and what kind of pings they have then make a decision based on that

What firmware version are you on at the moment? I know there was an update that improved speeds, you may be past it already though

I've sent you .23 in a PM, you can install it in Settings > Troubleshooting. Once it's complete I'd recommend doing a factory reset to ensure remnants of previous versions aren't causing any issues, then see it works better

It won't be doing anything at 100 so try 70 and experiment from there and you should notice a difference

You already have a port rule added, what was that one for?

Great to hear that, thanks for the update!

Does it show the ping graph with the upper limit being 50 at all or 27?