Jump to content

Issue getting R2 Setup


AceMan20
 Share

Recommended Posts

Howdy!

So I purchased an R2 router yesterday and followed the instruction booklet - but ultimately couldn't get it to function as intended. I have the router plugged into my ISP's modem, its the only wired device that is and my laptop wired to the R2 router. Doing this, I do have internet access (even when turning wifi off), my laptop identfies the router as "Network 2". Trying to download the OS and access the wizard is where my first problem occurs, it asks me for a username and password to access the site (used both dumaos/ and the IP), and no matter what I try, the site doesnt load, or it just asks me for the username/password again like I got it wrong. I found somewhere on this site that the password is "password" and the username is "admin" which is what I was using.

Interesting enough, when I turn wifi on, my laptop finds the netdumar2 router, but trying to connect to it using the password on the bottom of the router has yielded no results, just says "could not connect to this network". I believe I read that I would need to download the OS/set up wizard and do it before wifi can be enabled. 

I feel like my laptop when wired to the R2 router, isnt communicating to it right because its only labeled as "Network 2" and not "NetdumaR2" like the wireless is registering it as. Any tips or insights on how I could get connected to access the wizard?

 

(attached below are screencaps from the site asking for login credentials and also of my connection tab)

image.png

image.png

Link to comment
Share on other sites

1 hour ago, AceMan20 said:

Howdy!

So I purchased an R2 router yesterday and followed the instruction booklet - but ultimately couldn't get it to function as intended. I have the router plugged into my ISP's modem, its the only wired device that is and my laptop wired to the R2 router. Doing this, I do have internet access (even when turning wifi off), my laptop identfies the router as "Network 2". Trying to download the OS and access the wizard is where my first problem occurs, it asks me for a username and password to access the site (used both dumaos/ and the IP), and no matter what I try, the site doesnt load, or it just asks me for the username/password again like I got it wrong. I found somewhere on this site that the password is "password" and the username is "admin" which is what I was using.

Interesting enough, when I turn wifi on, my laptop finds the netdumar2 router, but trying to connect to it using the password on the bottom of the router has yielded no results, just says "could not connect to this network". I believe I read that I would need to download the OS/set up wizard and do it before wifi can be enabled. 

I feel like my laptop when wired to the R2 router, isnt communicating to it right because its only labeled as "Network 2" and not "NetdumaR2" like the wireless is registering it as. Any tips or insights on how I could get connected to access the wizard?

 

(attached below are screencaps from the site asking for login credentials and also of my connection tab)

image.png

image.png

The login is is Username : admin
password: password

Link to comment
Share on other sites

Have you gone through the setup wizard of the R2? That has to be done first! 

In your browser type in 192.168.77.1 There you should be greeted with the setup wizard..

If you cant access the setup wizard then factory reset the R2 by holding in the reset button on the back of the R2 for 30sec. Then release and wait about 2 minutes then proceed to try again. You should now be greeted with the setup wizard when you type in 192.168.77.1 

Again you have to go through the setup wizard to actually setup a password and complete the setup of the router.

Ive watched your video and it seems that is the problem. If you have purchased this router used or second hand then you cant log in until you factory reset the router and proceed through the setup wizard.

Hopefully this is what your having trouble with.

Good luck and welcome to the forum.

Thanks!

Zippy.

 

Link to comment
Share on other sites

1 hour ago, Zippy said:

Have you gone through the setup wizard of the R2? That has to be done first! 

In your browser type in 192.168.77.1 There you should be greeted with the setup wizard..

If you cant access the setup wizard then factory reset the R2 by holding in the reset button on the back of the R2 for 30sec. Then release and wait about 2 minutes then proceed to try again. You should now be greeted with the setup wizard when you type in 192.168.77.1 

Again you have to go through the setup wizard to actually setup a password..

Ive watched your video and it seems that is the problem.

Hopefully this is what your having trouble with.

Thanks!

Zippy.

 

Howdy Zippy!

 

Yessir this worked! Was able to access the wizard and set it up from there - however one smaller problem arose. I dont have the ability to connect devices to the Netduma using wifi - it doesnt show up on the wifi list like it did before. The only way I can access dumaOS is via wired. Is this intended?

 

Thanks so much in advance!

Link to comment
Share on other sites

2 hours ago, AceMan20 said:

Howdy Zippy!

 

Yessir this worked! Was able to access the wizard and set it up from there - however one smaller problem arose. I dont have the ability to connect devices to the Netduma using wifi - it doesnt show up on the wifi list like it did before. The only way I can access dumaOS is via wired. Is this intended?

 

Thanks so much in advance!

Connected wired, access the interface via 192.168.77.1 and head to "Network Settings" on the left hand side. Click "WIFI" and disable/un-toggle "Enable 2.4GHz and 5GHz WiFi". Next proceed to reboot the router from the top three dots in the top right corner and choose reboot. Once it's fully rebooted, this time enable/toggle on  "Enable 2.4GHz and 5GHz WiFi" and reboot the router once more. Might be some interference going on with the WiFi and just need a rebooting on the WIFI.

Link to comment
Share on other sites

8 hours ago, AceMan20 said:

Howdy Zippy!

 

Yessir this worked! Was able to access the wizard and set it up from there - however one smaller problem arose. I dont have the ability to connect devices to the Netduma using wifi - it doesnt show up on the wifi list like it did before. The only way I can access dumaOS is via wired. Is this intended?

 

Thanks so much in advance!

Well howdy to you AceMan!   Glad you were able to get it up and running. Try what TrayDay has mentioned with the Wifi.. I would think that should get the Wifi going as well.. If you continue to have problems post back here for further help!

Thanks!

Zippy.

Link to comment
Share on other sites

10 hours ago, Netduma Fraser said:

Hey, welcome to the forum!

Do try the method Tray suggested - it's exactly what I would have advised you to do. Let us know how you get on!

Howdy Fraser!

 

Yessir, this worked perfectly, although rebooting the router already set the enable 2.4 GHz and 5 GHz back to on instead of flipping it back on then rebooting it again. Connected to it just fine with the PW I set during the Wizard. Thank you so much y'all, no further questions!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...