kizvandutch Posted May 27, 2016 Share Posted May 27, 2016 I'm been having issues with getting nat with ps4 and the netduma. Is there a instruction steps i'm missing Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted May 27, 2016 Administrators Share Posted May 27, 2016 WAN IP of Duma in ISP hub DMZ. Disable UPnP/port forwarding on the ISP hub. Have UPnP or port forwarding enabled on the duma not both. You should have an open NAT on console network settings. Otherwise you can use Bagstas port forwarding guide http://forum.netduma.com/topic/15763-port-forward-for-blops3-on-ps4/ Link to comment Share on other sites More sharing options...
kizvandutch Posted May 27, 2016 Author Share Posted May 27, 2016 on my tp link should i have the duma mac address or ps4 mac address put in Link to comment Share on other sites More sharing options...
kizvandutch Posted May 27, 2016 Author Share Posted May 27, 2016 my isp is conected with my tp link which is in bridge mode. but when i do my setup my ps4 is nat 2 and blk ops 3 comes in at moderate. maybe im doing something wrong? Link to comment Share on other sites More sharing options...
kizvandutch Posted May 27, 2016 Author Share Posted May 27, 2016 isp modem is in dmz mode with my tp link and my tp link is dmz with my netduma if you were wondering Link to comment Share on other sites More sharing options...
Zennon Posted May 27, 2016 Share Posted May 27, 2016 You do not need to DMZ at modem level just the Netdumas WAN IP in the Tp Link's DMZ. Do that with the console off. Turn off the TP and duma after setting it up. Turn on the TP wait for it to fully boot then boot the duma then boot the console. Link to comment Share on other sites More sharing options...
kizvandutch Posted May 28, 2016 Author Share Posted May 28, 2016 Upnp should be on tp link and netduma settings? Link to comment Share on other sites More sharing options...
kizvandutch Posted May 28, 2016 Author Share Posted May 28, 2016 Zennon didn't work. But my ps4 says nat 2. Link to comment Share on other sites More sharing options...
Zennon Posted May 28, 2016 Share Posted May 28, 2016 NAT2 is correct, Turn off the console go to the dumas settings / UPnP / un tick enable press apply (you may have to refresh the screen) re tick enable press apply (again a refresh may be needed) Turn back on the console. Link to comment Share on other sites More sharing options...
kizvandutch Posted May 28, 2016 Author Share Posted May 28, 2016 same issue. Link to comment Share on other sites More sharing options...
kizvandutch Posted May 28, 2016 Author Share Posted May 28, 2016 lan settings for my tp link should be the netduma or tp link ip address? Link to comment Share on other sites More sharing options...
Zennon Posted May 28, 2016 Share Posted May 28, 2016 I do not know what you are trying to change there , just leave that alone. The WAN IP of the netduma into the TP DMZ only. Link to comment Share on other sites More sharing options...
kizvandutch Posted May 28, 2016 Author Share Posted May 28, 2016 dhcp should be my tp link ip address? Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted May 29, 2016 Administrators Share Posted May 29, 2016 Leave DHCP as it is on the duma currently. You don't need to change that in order to achieve an open NAT. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.