NEW XR500 BETA FIRMWARE: 3.3.535

[Netduma Fraser]

21 minutes ago, IITazII said:

no

How are you doing it, via the interface or the big physical button? I suspect it's losing power in that case if you're not unplugging it or factory resetting it from the pin or interface. Is it connected to an extender or direct to an outlet?

[IITazII]

10 minutes ago, Netduma Fraser said:

How are you doing it, via the interface or the big physical button? I suspect it's losing power in that case if you're not unplugging it or factory resetting it from the pin or interface. Is it connected to an extender or direct to an outlet?

I tried both ways but it keeps resetting to factory settings.

The problem is that it doesn't save the settings after starting the router.

[Netduma Fraser]

1 hour ago, IITazII said:

I tried both ways but it keeps resetting to factory settings.

The problem is that it doesn't save the settings after starting the router.

It must be losing power then during the reboot, I don't see any other reason why that would be happening, do you have it connected to an extender or direct to an outlet? Do you have another power adapter with similar voltage you can use to test?

[IITazII]

On 6/25/2025 at 2:56 AM, PurpleHaze said:

The chip is if anyone wants to know, at least on mine is a 

MXICx174514

30uf2618AC-XOI

8C374700

Its under the big heat sync on the bottom held in place by dimples, can be tricky to open.

This requires a nand flash not SPI, so support may be limited, unfortunately you can (I don't think) get a flash clip onto it. Will require desoldering and flashing best done by a professional experienced micro solder.

GPT says that using a CH341A SPI programmer could solve this problem.

 

or is it already solved?

[PurpleHaze]

On 7/5/2025 at 5:55 PM, IITazII said:

GPT says that using a CH341A SPI programmer could solve this problem.

 

or is it already solved?

Hi thank you, I think it will need to be desoldered flashed and resolsdered. Managed to find another one second had. GPT is mighty helpful but you need to be careful with stuff like this as I believe that's incorrect. I dont believe the clip would get under the chip? I have a very similar soic 8 clip that I might test fit to compare. Thanks 😊 

[Suad]

Good news guys. All my DHCP issues were fixed since I installed official update V2.3.3.136. 

I have been using this firmware for 3 months, and I never encountered any issues. 

[L7NALMARI]

On 7/24/2023 at 8:46 PM, Netduma Fraser said:

See if you can upgrade to this one: https://www.dropbox.com/s/mb7hztmwpxnpz2i/XR500-V2.3.2.134-dumaos33-rc10.img?dl=0 then upgrade to the beta

[L7NALMARI]

What the last update for xr 500 ?

i have now v2.3.2.134-dumaos33-tc14 @Netduma Fraser

[Netduma Fraser]

9 hours ago, L7NALMARI said:

What the last update for xr 500 ?

i have now v2.3.2.134-dumaos33-tc14 @Netduma Fraser

That is the latest from us yes and would advise you stay on that one instead of going to some of the more recent public versions - they don't have anything different

[L7NALMARI]

11 hours ago, Netduma Fraser said:

That is the latest from us yes and would advise you stay on that one instead of going to some of the more recent public versions - they don't have anything different

Is this the most stable or should go older ? 

[Netduma Fraser]

12 hours ago, L7NALMARI said:

Is this the most stable or should go older ? 

I'd suggest staying on this version yes, its the best in my opinion