NTB318 Posted December 10, 2016 Share Posted December 10, 2016 Now my ISP is At&t and using a residential router instead of modem will netduma still work Link to comment Share on other sites More sharing options...
Slipknot31286sic6 Posted December 10, 2016 Share Posted December 10, 2016 Yes jus give netduma a static up or dmz is recommended if u can Link to comment Share on other sites More sharing options...
NTB318 Posted December 10, 2016 Author Share Posted December 10, 2016 Ok do u have instructions on how to do that Link to comment Share on other sites More sharing options...
Slipknot31286sic6 Posted December 10, 2016 Share Posted December 10, 2016 Copy and paste form ATT website, I know it says NVG589 but should hlpe and be very similar to 599. Default is 192.168.1.254 Go to 'Home Network' then 'Subnets & DHCP'. Your password is on the side of the modem. If your 'Device IPv4 Address' is the same subnet as your local router, I suggest changing it. I changed mine to 192.169.2.254 but you can stick with whatever you like / need. My subnet Mask remains at 255.255.255.0 Change 'DHCPv4 Start Address' to 192.169.2.1 (or whatever your above Device IPv4 address is but with a 1 at the end instead of .254) Change 'DHCPv4 End Address' to 192.169.2.5, Just a few more than the Start Address. We need these for any WAP extenders for wifi TV's. It's important that you only have the laptop plugged into the ethernet at this point. Click 'SAVE' at the bottom. Go to 'Home Network' then 'Wireless' and turn wireless off. You want to use the wifi on your own router right? Go to 'Firewall' then ' 'Packet Filter'. Disable Packet Filters. Again, we want our router to do the work. Make sure you don't have any of your own settings turned on in 'NAT/Gaming' (don't worry if you see 1 in there already that you can't delete). Go to 'Firewall' then 'IP Passthrough'. For 'Default Server Internal Address', select or type in 192.169.2.1. For 'Allocation Mode' select 'Passthrough' (I had to do it in this reverse order to be able to type for some reason) For 'Passthrough Mode', select 'DHCPS-Fixed' Type in the MAC address for your router under 'Manual Entry', lowercase is fine. Click SAVE. It will tell you that it needs to reboot. Hang on for a minute. Go to 'Firewall Advanced' at the top and turn everything OFF. Near the top of your screen, you should see an option telling you to reboot the router. Go ahead and do this now. It takes about 2 minutes. Personal Router Settings. Unplug your laptop and plug in your personal router while the NVG589 reboots. Plug your laptop into your personal router and login to it. For me, it was 192.168.1.1 (hence why I changed things above) For the ASUS RT-N66U, I had to go to my WAN settings, then 'Internet Connection'. Change 'WAN Connection Type' to 'Automatic IP'. This will give your personal router the external IP of the NVG589 and is the key to making this whole thing work. Some folks will have to manually enter in an IP and this can be found under the 'Broadband - Status' section of the NVG589 settings. If you don't have 'automatic IP' then I feel bad for you since you will have to manually change this every time your IP changes. 'Enable WAN', 'Enable NAT' and 'Enable UPnP' is all set to YES for me. I recomend Setting your own DNS server. I use Google's but you use whatever you like. Google's is 8.8.8.8 and 8.8.4.4 'Account Setting - Authentication' is 'None'. There are no Special requirements from ISP at the bottom. Hit APPLY at the bottom and your router will reboot. I also changed settings in my IPTV under LAN: Profile was None. Choose IPTV STB port, I set to LAN3 & LAN4. I plugged my U-Verse WAP for the wireless reciver into the NVG589 and I plugged the ethernet cable going to the VIP2250 into LAN3 on my personal router. I'm really not sure if this was necessary but I'm having 0 issues with this setup. I initially tried putting the WAP on my personal router but had issues so I stuck it back on the NVG589 and it's fine. I could probably just plug the VIP2250 into the NVG589 as well but I'm just enjoying the small victory of using my personal router for now. Hit apply at the bottom, another possible reboot. At this point, I checked the internet and everything was working great through the router. I restarted by 2 TV boxes (the VIP and the wifi ones). Everything is peachy. Your mileage may vary. Good luck. Posted by someone else Link to comment Share on other sites More sharing options...
fuzzy clam Posted December 10, 2016 Share Posted December 10, 2016 Yeah it will work with AT&T equipment,I have a dedicated gaming line with them as my ISP. The way there all in one modem and router combo works is kind of a pain but you only gotta do it once... http://forum.netduma...z-r1-on-uverse/ I would use this guide Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted December 12, 2016 Administrators Share Posted December 12, 2016 Hey, welcome to the forum! Yes you should be absolutely fine to do that Link to comment Share on other sites More sharing options...
Spartanogc Posted December 12, 2016 Share Posted December 12, 2016 I just moved and Comcast does not provide service so I had to switch to ATT also. Link to comment Share on other sites More sharing options...
fuzzy clam Posted December 13, 2016 Share Posted December 13, 2016 I just moved and Comcast does not provide service so I had to switch to ATT also. It shouldn't be an issue at all, just follow the guide I posted above and you should be good to go. If you run into any issues just post back and we'll get you sorted out. Link to comment Share on other sites More sharing options...
Spartanogc Posted December 28, 2016 Share Posted December 28, 2016 Fuzzy my modem/router is different its a Pace 5268 AC, the setup is different. Would you happen to know how make the changes in this model? Link to comment Share on other sites More sharing options...
Alex49H Posted December 28, 2016 Share Posted December 28, 2016 Fuzzy my modem/router is different its a Pace 5268 AC, the setup is different. Would you happen to know how make the changes in this model? I have the same router/modem the 5268ac and this is what I did: There is no true bridge mode on the 2Wire routers. However, you can still configure it such that almost all functions of your own router will work properly. 1. Set your router's WAN interface to get an IP address via DHCP. This is required at first so that the 2Wire recognizes your router. 2. Plug your router's WAN interface to one of the 2Wire's LAN interfaces. 3. Restart your router, let it get an IP address via DHCP. 4. Log into the 2Wire router's interface. Go to Settings -> Firewall -> Applications, Pinholes, and DMZ 5. Select your router under section (1). 6. Click the DMZPlus button under section (2). 7. Click the Save button. 8. Restart your router, when it gets an address via DHCP again, it will be the public outside IP address. At this point, you can leave your router in DHCP mode (make sure the firewall on your router allows the DHCP renewal packets, which will occur every 10 minutes), or you can change your router's IP address assignment on the WAN interface to static, and use the same settings it received via DHCP. 9. On the 2Wire router, go to Settings -> Firewall -> Advanced Configuration 10. Uncheck the following: Stealth Mode, Block Ping, Strict UDP Session Control. 11. Check everything under Outbound Protocol Control except NetBIOS. 12. Uncheck NetBIOS under Inbound Protocol Control. 13. Uncheck all the Attack Detection checkboxes (7 of them). 14. Click Save. Link to comment Share on other sites More sharing options...
fuzzy clam Posted December 29, 2016 Share Posted December 29, 2016 I would say follow alex's guide as AT&T has apparently switched modem / router combo's again, hopefully they upgraded them as my is glorified garbage. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.