BSilverthorn

Are there any known issues with this feature on XR1000V1. It seems like it use to work fine, unless I am blurring this with my XR700 that died. It currently does not seem to be blocking anything even though it is enabled. This a full factory reset and fresh setup as of this AM. Firmware: XR1000 1.0.0.68_1.0.54

Below is the entry from the logs on the router, 10.1.1.1 is the internal side of VZ modem. One curious if this repsonse is valid as the VZ firewall is on and would not think it would let that thru to the internal. But I guess my other question is I see this often, a few times a day, Could I not just forward 67 and 68 to some bogus port that doesnt respond to anything to maybe assist in going away? [DoS attack: Fraggle Attack] from source 10.1.1.1,port 67 Wednesday, Feb 28,2024 03:39:23 [DoS attack: Fraggle Attack] from source UNKNOWN,port 68 Wednesday, Feb 28,2024 03:39:22

I'll check openWRT, warranty is gone now. If it happens again when the new firmware comes out ill let you know and grab the logs. For now, Iam close to going office space on it so best it run something else, and move on. Not to concerned on getting back to Duma, I saved all the old firmwares so I can TFTP. If I can't I just get more time back added back. Thanks Fraser, ill take a look. Apprecaite all your help.

10.1.1.1 Very odd behavior, but I just switch the router out and im back up. Factory reset sometimes does it as well. So odd, as no rapp errors, no slowness per say. Just traffic stops. leave off for a day, makes do difference.

So in less than 2 months for 3 rd time in 9 months I back to XR1000 not routing again. Looks healthy, can login, etc.. It just magicly gets slow then stops routing, numerous reboots or power offs do not fix it, the only fix is the TFTP solution basicly. Luckily now I keep a cheap TPlink router setup and on for when this thing pukes, so I just move 3 cables and the house is back online, while I tftp the darn thing. While I wait on the next firmware release, I was curious if anyone has a 3rd party suggestion, I do not see the XR1000 on openwrt or freshtomato. I don't want to reload this again, its just to much to mess with so often. Looking for alternative until the new firmware releases for XR1000. Any have any another solution they are running on the XR1000?

That seem to resolve the issue, the bigger question is why ?

ill try it in the AM and see what happens, thank you!

Found this post: I have done everything in this post and probably more.

I just Tftp a new image on to my XR1000. Everything seems to be 90% better now other than this error. I can't set home point? Can't draw it, place a way point. I can search it, it looks it up, but then applying it I get this error: Firmware: XR1000 1.0.0.68_1.0.54 Tried in incognito Tried Firefox, Chrome, FireDragon, Tried on Windows, Unix Armor is not enabled, never has been Add Blocker is disabled Disabled all browser extensions rebooted router numerous times https and http Increased time to 5 from 3 for rapps

I run my own internal DNS server & DHCP server. Is there a magic trick I can use to get the XR1000 to look at my 192.168.1XXX lan name resolution of the internal devices? Would be great if it use the DNS server to populate the names instead of just always unknown.

Yes, it is the worst netgear router I have ever owned. Wish I would have returned it! I have to reflash the firmware often, DUMAOS not loaded 5 to 6 times a year, along with rapps not loading etc... I should have never sold the XR500, it was for the most part rock solid. I have told many to pass on XR1000 series. I don't blame duma though, these guys up here try to help. Hopefully 3.3 will help this old dog in so many ways, someday. These are my icons right now lol, I just dont have time to reflash it again. I'm back to this again after reboot as well: Wan IP is a 10. and sub net is differnet as well. May not wait on 3.3 and just go get a new router at microcenter.

Yes it does, the name and ip are correct.

Right now as I took this snip, I have a device pulling down over 150 MBs. But it does not show when I go to the dashboard or too network monitoring. It is a ghost? I know its doing it, as its my PC and use to show up. Its updating Microsoft Flight Simulator and it is stating the correct network speed. Any ideas on this? None of the list devices, is the PC I am.

I resolved this by disconnecting everything from the router, connecting via wifi, then it let me turn dhcp off. Saved settings and rebooted. I seem to be working but sure is the hard way to disable DHCP

I also double checked to see if there was some weird reason that something came online as 1.1. When the router is off pings fail to 192.168.1.1. Wireshark just shows DHCP requests not getting answered.

Piehole setting, I turned DHCP off since I can not disable the router for some reason.

It is at 192.168.1.223 for DNS and DHCP

192.168.0.1 is it, the IP of XR100 WAN port is 192.168.0.150. Been this way for a year or two at least, not that matters. If I can access the router at 192.168.1.1, why can't I just stop the DHCP service from running?

Came home and had to do a hard reset of the router for some reason. Now when attempting to turn off the DHCP portion of the router I recieve the following error: I know this should be a simple straight forward thing and I understand subnetting, My verizon modem that the XR1000 is plugged into has not been update or changed in reference to IP, subnet etc. Usually I just rest have to reset the router once every 3 to 5 months, login and turn off the DHCP server. I never recieved this. I dont want to re-ip my enter house to a differnt network atm don't have time. So not sure what is amiss here. I know its a Mr Obvious, my router has been 192.168.1.1 on the internal side. With DHCP coming from the piehole server. Why? And why isnt the IP address conflicting now with the check to use DHCP server enabled, I dont want a differnt IP. I just want the darn DHCP server off. Also reflashed the firmware just for kicks late last night to see what gives.

Any other url to get in vs this factory reset. I kept getting sent back to this, even after success of new password and security questions: I have gone thru this 3 times. I loath this screen when it happens, would like nothing more to disable it. I under stand the security behind it, but when your behind two other firewalls already ;-).

Yep, I do that now, I run my own DHCP server. I have less lockups or responvies issues wtih XR700 using a standalone solution for DHCP, it seems to ignore the names from the DHCP / DNS internal server when they reconnect. So I name most them manual in devices, but a bit of undertaking at times. I have exported my DNS records and will try to import that into the devices window.

Unfortnately it appears to also remove the good devices that are named at the same time. If my TV is off or the APPLE-TV, it removes those as well. Would love to just be able to tag the ones I want deleted and have it do a mass remove.

Is there way to mass delete. Seems like a year or two back this was a thing coming? Id like to be able to "just" delete all the unnamed.dev devices. But not "all offline" devices as just because there are offline does not mean they are invalid etc.. I have learned the android and ios devices on my network consistenlty spoof thier identity per say ;-). I love the idea and the feature but not on my home network. Instead of sitting here once a month for any clicking the device and hitting delete and rinse and repeat. unnamed device

Is Microsoft Teams classified under the "Work At Home" in the QOS Section? I noticed my voice traffic is lagging at times. Could be teams, but I having trying to find away to give this app top prioity on the network during 8-5 since it has replaced phones etc now for work at home. I see the video option under there when added by device, but curious on the voip side of teams.

Good question, I will do some snooping and see. Thank you