DeeKay_FPS Posted January 5 Share Posted January 5 Just got the R3 today and noticed geo-filter is not working as intended. I connect to games outside my range. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted January 5 Administrators Share Posted January 5 Disable GeoLatency Disable PingAssist (set it to 0,0) Enable Strict Mode Disable Fast Search Then restart game or wait 10 minutes (in the lobby in the game). If that doesn't work, reboot PC/Console and it should work then. Link to comment Share on other sites More sharing options...
DeeKay_FPS Posted January 6 Author Share Posted January 6 I followed the steps you've mentioned but seems like i still have issues. Its not searching the games with specified ping/radius. Link to comment Share on other sites More sharing options...
DeeKay_FPS Posted January 6 Author Share Posted January 6 Sorr if this is a stupid question. The whole point is to restrict the Geo-location so I get low ping lobbies. May I know why you are suggesting to switch of GeoLatency. I'm a bit lost. Link to comment Share on other sites More sharing options...
DeeKay_FPS Posted January 6 Author Share Posted January 6 Also my firmware is 4.0.20 Link to comment Share on other sites More sharing options...
LightsOut Posted January 6 Share Posted January 6 I had the same problem while playing COD. Did the following: Disable GeoLatency Disable PingAssist (set it to 0,0) Enable Strict Mode Disable Fast Search And still had the same issues of connecting to servers I had geo-filtered to be "off." Only way I got it to actually work was to go into the Geo-Filter Tab, then I fired up the game. At that point, the Geo Filter Tab showed all of the servers available to connect to. I then single handedly went to each of the servers I could see and clicked on them then told the router to deny connection.... one by one until only the two servers that were suitable to connect to were available. I think at this point, I could delete my custom geo filter and it would probably still work BUT I shouldn't have to do all that, right? Isn't that the point of having a custom filter, so that you don't have to deny servers connections? oldman66 1 Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted January 6 Administrators Share Posted January 6 12 hours ago, DeeKay_FPS said: Sorr if this is a stupid question. The whole point is to restrict the Geo-location so I get low ping lobbies. May I know why you are suggesting to switch of GeoLatency. I'm a bit lost. I've sent you the .23 firmware via PM, see if that helps at all. Geo-Latency is a filtering method just like using the radius/polygon so you're just switching the way you're filtering, getting low ping servers is still possible. 10 hours ago, LightsOut said: I had the same problem while playing COD. Did the following: Disable GeoLatency Disable PingAssist (set it to 0,0) Enable Strict Mode Disable Fast Search And still had the same issues of connecting to servers I had geo-filtered to be "off." Only way I got it to actually work was to go into the Geo-Filter Tab, then I fired up the game. At that point, the Geo Filter Tab showed all of the servers available to connect to. I then single handedly went to each of the servers I could see and clicked on them then told the router to deny connection.... one by one until only the two servers that were suitable to connect to were available. I think at this point, I could delete my custom geo filter and it would probably still work BUT I shouldn't have to do all that, right? Isn't that the point of having a custom filter, so that you don't have to deny servers connections? No you shouldn't need to do that, what firmware version are you on? Link to comment Share on other sites More sharing options...
LightsOut Posted January 11 Share Posted January 11 On 1/6/2024 at 7:18 AM, Netduma Fraser said: I had the same problem while playing COD. Did the following: Disable GeoLatency Disable PingAssist (set it to 0,0) Enable Strict Mode Disable Fast Search And still had the same issues of connecting to servers I had geo-filtered to be "off." Only way I got it to actually work was to go into the Geo-Filter Tab, then I fired up the game. At that point, the Geo Filter Tab showed all of the servers available to connect to. I then single handedly went to each of the servers I could see and clicked on them then told the router to deny connection.... one by one until only the two servers that were suitable to connect to were available. I think at this point, I could delete my custom geo filter and it would probably still work BUT I shouldn't have to do all that, right? Isn't that the point of having a custom filter, so that you don't have to deny servers connections? The version it shipped with which is v4.0.20. I could be blind but I'm not seeing a setting where I can check if the firmware is up to date? Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted January 11 Administrators Share Posted January 11 9 hours ago, LightsOut said: The version it shipped with which is v4.0.20. I could be blind but I'm not seeing a setting where I can check if the firmware is up to date? I've sent you .23 via PM, you can upgrade from Settings > Troubleshooting, once complete I'd recommend doing a factory reset Jumppy_15 and LightsOut 2 Link to comment Share on other sites More sharing options...
LightsOut Posted January 12 Share Posted January 12 10 hours ago, Netduma Fraser said: I've sent you .23 via PM, you can upgrade from Settings > Troubleshooting, once complete I'd recommend doing a factory reset This firmware should fix the geofilter not working, yes? Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted January 12 Administrators Share Posted January 12 8 hours ago, LightsOut said: This firmware should fix the geofilter not working, yes? It does have some Geo-Filter improvements yes but we'll be continuing to improve it in subsequent firmware LightsOut 1 Link to comment Share on other sites More sharing options...
LightsOut Posted January 15 Share Posted January 15 Tried the new firmware and it looks like some servers are still getting through the geo-filter but if I disable them, it doesn't connect to them. Not sure why they're getting through the custom geo-fence but just an FYI that they are. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted January 15 Administrators Share Posted January 15 9 hours ago, LightsOut said: Tried the new firmware and it looks like some servers are still getting through the geo-filter but if I disable them, it doesn't connect to them. Not sure why they're getting through the custom geo-fence but just an FYI that they are. Thanks for the feedback, more Geo-Filter improvements will be on the way Link to comment Share on other sites More sharing options...
Spiff Posted February 19 Share Posted February 19 Same issue, see that you have been sharing an update file? Cant get geofilter to work properly Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted February 19 Administrators Share Posted February 19 35 minutes ago, Spiff said: Same issue, see that you have been sharing an update file? Cant get geofilter to work properly That was awhile ago, latest is .41 now: https://forum.netduma.com/topic/53938-new-r3-firmware-4041/ Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now