TheT Posted December 30, 2023 Share Posted December 30, 2023 My geofiltering is often connecting to other EU servers despite the radius being locked to UK. I was also hoping to see server tickrate, but I cannot seem to see it when I connect to a game server. Any help appreciated, cheers! Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted December 30, 2023 Administrators Share Posted December 30, 2023 Disable GeoLatency Disable PingAssist (set it to 0,0) Enable Strict Mode Disable Fast Search Then restart game or wait 10 minutes (in the lobby in the game). If that doesn't work, reboot PC/Console and it should work then. Tick rate isn't something the router shows, I can make a request for it though Link to comment Share on other sites More sharing options...
nowmat Posted December 31, 2023 Share Posted December 31, 2023 3 hours ago, Netduma Fraser said: Tick rate isn't something the router shows, I can make a request for it though R2 showed the server's tick rate, I miss this option... I don't understand why it was removed from R3. The tick rate is the refresh rate of the server, the higher it is, the better hit detection is. It would be nice to know. Link to comment Share on other sites More sharing options...
satinghostrider Posted December 31, 2023 Share Posted December 31, 2023 5 hours ago, TheT said: My geofiltering is often connecting to other EU servers despite the radius being locked to UK. I was also hoping to see server tickrate, but I cannot seem to see it when I connect to a game server. Any help appreciated, cheers! It shows for me on my end for MW3. Link to comment Share on other sites More sharing options...
sloon Posted December 31, 2023 Share Posted December 31, 2023 (edited) it never shows me this table 100x connect only host , deticated server 0x (steady ping on Edited December 31, 2023 by sloon foto Deasha 1 Link to comment Share on other sites More sharing options...
johnnytran Posted January 1 Share Posted January 1 18 hours ago, sloon said: it never shows me this table 100x connect only host , deticated server 0x (steady ping on This is a known bug that's being looked into. It happens to me as well (I have never been able to see tickrate or the stabilised ping graph shown a few posts above) Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted January 1 Administrators Share Posted January 1 On 12/31/2023 at 9:33 AM, sloon said: it never shows me this table 100x connect only host , deticated server 0x (steady ping on You won't always be able to ping a server so when you see that specifically it is likely for good reason. What firmware version are you on? Link to comment Share on other sites More sharing options...
sloon Posted January 1 Share Posted January 1 2.0.23 geo-latency off , pingassist 0.0 , strict on , fastsearch off gaming pc how console (better filtering) , smart qos off ...th Link to comment Share on other sites More sharing options...
sloon Posted January 1 Share Posted January 1 manual ping in gameplay Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted January 2 Administrators Share Posted January 2 How do you have the ISP modem/router setup to allow an uninterrupted traffic flow to the R3? As that could be affecting your ability to ping Link to comment Share on other sites More sharing options...
TheT Posted January 2 Author Share Posted January 2 25 minutes ago, Netduma Fraser said: How do you have the ISP modem/router setup to allow an uninterrupted traffic flow to the R3? As that could be affecting your ability to ping I genuinely have not checked this. I use communityfibre and have a linksys MX4200 - What setting would I need to check to make sure nothing is interrupting the R3? Link to comment Share on other sites More sharing options...
TheTerpinator710 Posted January 2 Share Posted January 2 6 hours ago, Netduma Fraser said: How do you have the ISP modem/router setup to allow an uninterrupted traffic flow to the R3? As that could be affecting your ability to ping curious too, im on xfinity isp.. what should i do? Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted January 2 Administrators Share Posted January 2 On the modem/router ensure it's in modem or bridge mode or my personal favorite, copying the WAN IP from the R3 Settings > WAN page and then entering that in the DMZ on your modem. That will allow all traffic to flow directly to the R3. Link to comment Share on other sites More sharing options...
x12Tyler Posted January 2 Share Posted January 2 On 12/30/2023 at 10:49 PM, satinghostrider said: It shows for me on my end for MW3. I don’t think that’s accurate. Their server tick rate is like 12 or something like that. I knows it’s 20 or less definitely not in the 60’s. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now