OneOnline Posted September 26, 2021 Share Posted September 26, 2021 Hello, have a look at my log for the last 3 minutes, how can I fix these errors? Sat Sep 25 20:28:41 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:28:25 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:28:09 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:27:53 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:27:37 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:27:25 2021 daemon.err odhcp6c[1948]: Failed to send DHCPV6 message to ff02::1:2 (Address not available) Sat Sep 25 20:27:21 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:27:05 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:26:49 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:26:33 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:26:17 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:26:01 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:25:45 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:25:29 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) Sat Sep 25 20:25:17 2021 daemon.err odhcp6c[1948]: Failed to send DHCPV6 message to ff02::1:2 (Address not available) Sat Sep 25 20:25:13 2021 daemon.err odhcpd[1370]: Failed to send to ff02::1%lan@br-lan (Address not available) And in Geo-Filter and other tabs, I see errors like this: Uncaught TypeError: Cannot read properties of undefined (reading 'setTour') and after skipping tour Uncaught TypeError: Cannot read properties of undefined (reading 'fireTourFoundHere') Tours don't work at all. I guess it doesn't matter, but who knows what is wrong with my device, because I remember that they worked before on the same firmware that I had before the factory reset. I'm pretty sure my device is clean and set up correctly as I've gone through the entire update / reboot / reset etc. process 2 times. And a few errors that I saw a little later: daemon.err miniupnpd[2489]: try_sendto failed to send 12 packets <== this one repeats daemon.err cli.lua[2908]: uci: Entry not found cron.err crond[1405]: USER root pid 31564 cmd echo 3 > /proc/sys/vm/drop_caches Link to comment Share on other sites More sharing options...
Newfie Posted September 26, 2021 Share Posted September 26, 2021 Sometimes logs show stuff that’s there from the go and Fraser will know more what they mean but if you notice an issue and a reset does not solve it like the tours and you are worried the best way is to install the firmware over the top and reset using the rear pinhole then test again. sometimes a little gremlin sneaks in and needs to be cleared out. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted September 26, 2021 Administrators Share Posted September 26, 2021 The logs show normal background processes and are more for the developers rather than users as common entries can appear like issues when they're not, for example, the first is either because you have IPv6 disabled and your connection is IPv6 compatible or you have IPv6 enabled and your connection isn't IPv6 compatible - it won't cause any problems. What happens when you try to start a tour from the top of the Geo-Filter page for example? What web browser are you using? I would say if you're not having any issues as such to ignore the logs. If you're concerned a reinstall and hard reset as above is a good idea. Link to comment Share on other sites More sharing options...
OneOnline Posted September 26, 2021 Author Share Posted September 26, 2021 8 hours ago, Netduma Fraser said: The logs show normal background processes and are more for the developers rather than users as common entries can appear like issues when they're not, for example, the first is either because you have IPv6 disabled and your connection is IPv6 compatible or you have IPv6 enabled and your connection isn't IPv6 compatible - it won't cause any problems. What happens when you try to start a tour from the top of the Geo-Filter page for example? What web browser are you using? I would say if you're not having any issues as such to ignore the logs. If you're concerned a reinstall and hard reset as above is a good idea. When I open Geo-Filter page I see this: Uncaught TypeError: Cannot read properties of undefined (reading 'setTour') then I click OK and click GET STARTED to watch the guide, I see this: Uncaught TypeError: Cannot read properties of undefined (reading 'fireTourFoundHere') I have the latest version of Chrome browser (94.0.4606.61), only one AdblockPlus plugin and it is disabled for "192.168.77.1" so it shouldn't be a problem, also I cleared the cookies for "192.168.77.1" just in case but it did not help. I just tested this in Firefox and everything works fine, so the problem is obviously in the way Chrome works. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted September 26, 2021 Administrators Share Posted September 26, 2021 Thanks for the information, Chrome is one of our most tested browsers so it should be fine, what firmware version are you on? A hard reset using the button instead of the interface should definitely clear that Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.