Shecki

Absolutely. I appreciate all of the help through the correspondence. Thank you.

No worries. Gave that a go. Still won't load up.....

Still nothing. Again, went through all the steps this morning to try and just get this router to reset back to factory so that I can try and actually use it as it was intended. Hoping to see the light at the end of this tunnel soon. Thanks for your help.

Still no WiFi lights at all as well....

Hi Fraiser. Tried it, got nothing. Page wouldn't load.

It was updated with the current version the last time it was up and running...able to get to the dashboard. I don't think you guys have changed it in a couple of months, correct? And yes, it's always been the power adapter that came with the unit.

I hadn't used it in a bit because we were renovating the office here. I started using it again about 2 or 3 weeks ago. It went into DumaOS the first time I plugged it in and tried to get to the dashboard....and did so successfully. Ever since then, it has just been doing the same thing talked about in this thread.....which is essentially just a switch with no ability to get to the dashboard.

Is there a way to just set this thing back to the way it came out of the box? I've tried both unplugging it for a bit and holding the reset down for over 30 seconds....and neither seem to get this router back to working. Still strange though that I run both PC's through it without a problem. I just can't use the DumaOS functionality.

It's not registering a WiFi signal. Neither of the Wifi lights on the R2 are even lit.

The motherboards for both of the PC's in this office don't have wifi capabilities. I won't be able to join a wireless network with them.

Problem I’m having now is that the ports that have lan plugged in from PC’s (port 1 and 3) will go solid for about 3 seconds, shut off for about 7 seconds and just repeat this over and over. They never stay solid.

Liam, absolutely. But, before I do that.....what are you considering a reboot? Unplugging, letting it sit for a bit and then plugging it back in? Or holding reset for 30 seconds and then releasing the reset button?

Auto DHCP

Not to my knowledge. How would I go about checking to see if that's the case?

I've done that.....same result. In fact..... I just tried it again, and after holding in the reset for over 30 seconds, it wouldn't even reset.

When I punch in the xfinity gateway address, it pops up no problem.....even though this PC is going into the R2 (again, that is going into the Xfinity modem). It's like it's bypassing right past the R2 and using it as a switch or something....and not being recognized as a router.

Yep. I actually just did it again with the same result. I'll post both screenshots. One of 10.0.0.1 after it would not load and then right after that, I an command and still got a default gateway with that address....

Uplugged the WAN from the R2, went to the command prompt and typed in ipconfig and this is what I got. It looks pretty similar. Same 10.0.0.1 even with no WAN in.

Just gave it a try.....same one as before. By rebooting it, I assume you just mean unplugging it, unplugging the WAN line, plugging it back in letting it boot up and then re-connect the WAN. I didn't "reset" it because you didn't mention anything about the reset button on the back.

That address is for the Xfi router/modem from Xfinity, but yes, that PC is lan in right from the R2. That’s what I was trying to explain. I’m def going into the R2, but it’s coming up with that address in ipconfig.

Absolutely.

I probably should've mentioned, I'm getting ethernet to the R2 from an Xfinity Xfi modem. This PC however is running directly from the R2. Also, at one point, right when I hooked the R2 up, I was able to get to Duma OS. I need 6 lines for connection in this room, so both routers I have don't have enough lan outputs by themselves.

I get that on any both firefox and edge.

Absolutely!