Jump to content

Toxic Smoggie

Members
  • Content Count

    39
  • Joined

  • Last visited

Everything posted by Toxic Smoggie

  1. If you've got an Xbox One, might be worth running a detailed network statistics test with QoS disabled to see what speeds you are actually getting, failing that a PC\Laptop with Windows 7. Had an issue myself where my speed decreased and it took a lot of troubleshooting only to run a detailed network statistics test on the Xbox to notice that I was getting the speed I should be getting and then a re-installation of Windows 10 to find out it was an OS issue and not the Router\ISP which was causing the slow speeds. More recently had the same exact issue then googled it and found out that if you have Windows 10 that one of the updates for May/June caused the problem, reinstalled Windows again but straight after the 1809 update, downloaded and installed the 1903 update and so far so good.
  2. First of all would like to thank the Netduma Staff for all their help to get to the bottom of the issue, seems it wasn't a faulty modem or cable but a faulty driver issue within windows or Windows 10 itself that caused the issue. As the opening post went "After purchasing the Vigor 130, right from the off speed decreased from 53d/18u to 38d/18u but the ping remained the same (23ms)" Now the initial thoughts where with being on BT that I'd been banded as I had a new modem and that impacted my line, over several days there where a few disconnection over a 20 minute period, I could have been as my ping increased and it was a familiar issue that I've had before but it seems it could have been fixed after 2 weeks when my ping returned back to normal. But it seems that when plugging the Vigor 130 in, it may have corrupted something within Windows when it was speaking with the R1 and then XR500 when I plugged in the HG612, and why my speeds never got past 35 Mbps download for the R1 and 42\43 Mbps on the XR500 when I tested the HG612 modem. Most confusing part was when the setup wizard on the XR500 and later the internal speed test on the Xbox One come back with what I should be getting speed wise, to what was the laptop was getting, last night, decided to reset the laptop to back to factory settings, and now I can confirm that my speeds on the laptop are back showing as 55 Mbps download and 17 Mbps Just to finally add I'm in no rush to replace the Vigor 130 anytime soon and also if your facing speed issues, test the speed on the Xbox One if you have one, it's a good troubleshooting step and one I never thought of it until Tuesday but it can help eliminate the issue. Again thanks for all the help.
  3. On both the R1 and XR500 getting the 53/544 Mbps download speed and 17 Mbps upload speed on the Xbox when Disable QoS ticked, When High Priority Traffic Detected is selected and when Never is selected,, on the PS4 getting various speeds (to what I was getting on latest R1 original firmware), when its selected to Always getting what ever the sliders are set to or just under Unchecked the box and still get at least 53Mbps down and 17Mbps upload.
  4. Even the R1 on latest DumaOS firmware and 1.03.6j is doing the same thing, running a detailed network statistics on the Xbox One, it's showing as download speed 54Mbps and 17Mbps, on the PS4 it's showing download speeds of 52.1Mbps, upload 6.1Mbps Just testing the speeds through an Inspiron 15 Laptop running Windows 10, using Chrome and Firefox, the ethernet port in task manager won't get past 35Mpbs when testing the R1 or XR500, but others like the TP-Link, HH6, not a problem at all, will shows that the download speed will max out at 56/57Mbps, and this is only happening to the download speed, the upload speed isn't effected at all
  5. Don't have any other devices put have plenty of spare ethernet cable. So did a series of tests with some other ethernet cable and was running normal rate when plugged into the TP-Link, however when plugged into the R1 and XR500, was still getting the same speeds, also tried plugging the ethernet cable into the ethernet ports 2-5 on the R1 and ethernet ports 1-4 to rule out any port issues but was getting the same speeds. One thing I have notice is that running a detailed network statistics on the Xbox One, it's showing as download speed 54Mbps and 16Mbps, close to what I'd get on the XR500 in the setup wizard and on the PS4, 51.8Mbps
  6. I'm happy to have the TP-Link installed permanently to handle the PPPoE, as I've mentioned the setup's been modem > TP-Link > R1\XR500 and had no download speed issues until I put in the Vigor 130 then got issues with the R1, and then Sunday when I swapped the HH6 out for the HG612, used PPPoE on the XR500, then the download speed decrease. I've just done a test where I enabled Bandwidth Control on the TP-Link, give the laptop an IP address outside the IP address range setup on the TP-Link (below) And got the following speeds Also gone through the link http://support.netduma.com/support/solutions/articles/16000076586-dumaos-optimal-settings-guide-maxmimum-bandwidth-speeds Not sure what more I can do and its not just PPPoE that's slowing the download speeds on the R1\XR500, if it's DCHP or PPPoE, Static, the download speeds on the R1\XR500 are the same
  7. Yeah have used PPPoE on the R1 and XR500 and get 35mb download on the R1, 43mb on the XR500, the modem does have bridge-mode which is enabled, but I use PPPoE on the TP-Link (with bandwidth control turned off) and get my full download of 56mb down, all 3 still get 18mb upload, so only the download is being throttled, and tested all 3 with nothing else connected. Also with the HH6, don't need PPPoE enabled and have the same issues, Also Should note I'm using the Vigor 130 and not the HH6,, and have reset all 3 modems back to factory settings, so its all fresh settings and haven't changed any settings.
  8. I've had this set up since I got BT installed in September 2017 and bought the HG612. Modem > TP-Link > R1\XR500 (bought last year) The TP-Link's role was to handle not only the PPPoE but to also handle the other household devices, I put a bandwidth control on a range of address between 100 to 120, the speeds in the bandwidth control is 6mb down and 2mb upload, I entered the MAC address of the R1 and give it the ip ending in .42 so it was outside the bandwidth control and got all the bandwidth and it (basically followed This Video). Everything's been running fine for 20 months, no loss of speed of this magnitude from the R1 or XR500, have had to replace the HG612 with the HH6 but that's only when I've had some issue with my line and BT needed the HH6 in to test my line but no more than 4 occasions. Then in May 2019 I purchased the Vigor 130 modem and that's when it's all started, and it can all be seen in the OP. I can disable bandwidth control on the TP Link and plug the laptop in and I get full speeds, I can plug the laptop into the HH6 and can get full speeds, but when I've introduce a new modem in the last 4 weeks, my speeds on the R1 or XR500 have then reduced. The only times I've used PPPoE on the R1 is when I've been testing over the last 4\5 days, and the only time I've used PPPoE on the XR500 was yesterday when I wanted to check if the HH6 was blocking some ports that should be open (hence the Port Forwarding or Port Triggering? thread). What I'm getting in the R1 logs are whole lot of Not sure about the XR500 but did get this from one of the logs Sunday, June 09, 2019 22:56:29 [DumaOS] config write 'com.netdumasoftware.qos.settings', And that 9mb speed I said I was getting in the last post, might have been when testing the R1 as its back to 35mb
  9. That's the problem though, when I'm either on the Xbox or PS4, nothing is showing in UPnP, so not sure if it's enabled or not.
  10. So have reset the XR500 again back to factory setting and still seeing the download being limited to 42mb and upload is fine, however did notice that the sync speed is showing what I should be getting but the speed test is showing what I am getting which is a loss of 12/13mb Also test the R1 and now the download speed has gone down to 9mb, tested this on a new installation of Firefox and also deleted all the history and cookies in Chrome
  11. I'm guessing it's more of a software issue than a hardware one as the same thing has now just happened with the XR500 when I plugged the HG612 into it and now not getting download speeds no more than 42mb on that when I was getting 55/56mb earlier. So turned off the XR500, plugged the HG612 in, let it settle for 10 minutes, turned the XR500 on, went into setting so could set up the PPPoE, everything got connected, went to DSL reports and speedtest.net, was only getting a download speed of 42mb, upload speed was 16mb (was expecting some loss of speed but not 13mb for download), thought things weren't right, turned the XR500 off and unplugged the HG612, plugged in the HH6 and let it settle for 10 minutes, turned on the XR500, went into setting and turned off the PPPoE, ran a speed test and was still getting 42mb down but upload speed increase back to 18mb. reset the XR500 back to factory settings, ran another speed test and still get 42d/18u. I've plugged the laptop into the HH6 and Tp-link router and get 56 down and 18 up, even reset both back to factory settings and get the same results.
  12. Have an Xbox One and PS4 and play some of the same titles on both (not at the same time obviously), just wondering what's easier to set up for opening ports on the XR500
  13. So on both the R1 and Tp-Link router disabled UPnP and port forwarded port 80, went with the HG612 instead of the Vigor, but got the same results HG612 > R1 results HG612 > TP-Link results So then went to a familiar setup HG612 > TP-Link > XR500 Lost some speed with the HG612 and the TP-Link and the TP-Link and XR500 combo but only 5mb, but still only getting 35mb download with R1 but full upload
  14. UPnP has always been enabled both on the R1 and TP-Link (the TP-Link was connected to the HG612 and Vigor when it was setup for PPPoE), it's even enabled on the BT Hub and XR500 (where I'm able to get the full download speed), only used port forwarding for games. One test I did do this evening was plug in the Vigor 130, connect it to the TP-Link, configured the TP-Link for PPPoE so I could get the internet, turned bandwidth control off and was able to get full download speed, then connected the TP-Link to the BT Hub, again configured the TP-Link this time to dynamic IP (as the BT Hub already does the PPPoE), ran a speed test and again got full download speeds.
  15. screenshots as requested Also attached is the log file after the test as well Log attached log-1559934204992.txt
  16. Well had to use PPPoE when I tested it with the Vigor 130 as it's in bridge mode but using DCHP with it plugged into the HH6, the cpu doesn't go past 50%. Something strange did happen in the last 30 minutes that's back to normal, set the Download Bandwidth in the QoS to 56mb and Upload to 18mb ran a test and download speed never got past 35mb, set both sliders to 40%, download speed stayed at 35mb but upload went down to 6/7mb which is what I was expecting ran 3 tests and out of the 3 outcomes where the sliders where at 40%, all 3 tests came back as 35mb download speed and 6/7mb upload speed, typed in the value for the sliders to be at 100% and got the usual 35mb download speed and 17/18mb upload speed, then typed in the value for the download slider to be at 40% and then the download speed reduced to 20\21mb as it I was expecting from what was shown on from the QoS. Attached are two logs from within the last 40 minutes log-1559925836831.txtlog-1559925208002.txtlog-1559924950973.txt
  17. So plugged the Vigor directly into the R1, speeds are the same 35u/17d cpu usage between 80/90%
  18. It's not using either. For some reason the R1's download speed wont go more than 35Mbps.
  19. Did try a few things with the QoS, as I've had it set to "When High Priority Traffic Detected", changed this to Never, checked Disable QoS , had both Disable QoS checked and Anti Bufferbloat set to Never, no change in the speed, Bandwidth Allocation's never been touched and have gone as far as pressing the update\reset distribution. On the original firmware have the bandwidth set to 60 down and 20 up with both sliders at 100% and with either Proactive/Reactive selected, even gone as far as changing the Ethernet cable as well. Had the same configuration with the Vigor 130 > TP-Link > R1 with DumaOS that I did with the Openreach HG612 > TP-Link > R1 with DumaOS,, the TP link does have bandwidth control enabled but only from the range of 100 to 123, for 6d/3u and the R1 had a static ip ending in .50 The speeds tests are from DSLReports and Speedtest by Ookla
  20. ISP - BT Previous Setup -Openreach HG612\Vigor 130 > TP-Link > R1 with DumaOS Current Setup - HH6 > TP-Link > XR500 So had a pretty stable connection with the Openreach HG612 for the last 14 months, a few disconnections here and there but nothing to serious, was also getting a 53d/18u with a 23ms ping. After purchasing the Vigor 130, right from the off speed decreased from 53d/18u to 38d/18u but the ping remained the same (23ms), after a few issues speeds dropped further to 33d/15u and the ping increased to 31ms but after a week of line stability, the ping went back down to 21ms but speed remained low., at first I thought my land had be banded by BT as every speed test I did came back at 33d/15u. Yesterday phoned BT after 3 weeks from when the speed first dropped and they had me replace the Vigor 130 with the HH6, still getting the same speeds as I was before, was pretty much certain that my line had been banded by BT, until that is I saw my line stats on the HH6 router page and noticed that it was 60d/20u. So today after work,, I unplugged the laptop and plugged it into the TP-Link router and done a speed test which came back as 55d/18u, plugged the laptop into the HH6 and ran another speed test and got the same results 55d/18u, plugged the laptop into the R1 (which was connected directly to the HH6 and not the TP-Link) but now getting 33d/18u, factory reset and rebooted the R1 and still got the same speeds, reverted back to the original firmware, then did a factory reset, reboot and am still getting the same speeds. Currently have the Netgear XR500 plugged in but am getting the the speeds (approx) 55d/18u. Could this be failing hardware? R1 Speed Test R1 Speed test after the factory rest and reboot after downgrading to the original Firmware Speed test when plugged into the TP Link
  21. I've a similar problem myself with the HG612, where it lost at least 10 mbps download and 6 mbps upload. I had this connected for a few weeks and was getting speeds of 43/13 (download\upload) when doing a speed test and also what was reporting on the XR500 when checking the internet speed from the set up, from the HG612 stats program it was reporting: Sync (kbps) 56513 20000 Attainable rate (kbps) 61348 21870 Now the cabinet I'm on is an ECI cabinet, but today my speeds decreased from 43/13 to 29/12, not much lost in upload speeds but lost a further 14 mbps download speed, after disconnecting the HG612 and connecting the Home Hub 6 even though the Downstream and Upstream sync speed reports as 59.99/20 in the BT Smart Hub Manager stats, I'm now managing to get 54/18 when doing a speed test and also the XR500 picked up on as well.
  22. One thing I'd like to see in a future update would be able to lock in the values in the 'Set Device Bandwidth' in both upload and download, as it's a little annoying that you have to re-config the values if a device is added or removed.
  23. I set my Xbox One to Energy Saving from Instant-On and it seems to have 'fixed' the issue.
×
×
  • Create New...