BlackBoXBoSS Posted February 5 Share Posted February 5 I can't access DumaOS. Every time I try I am getting an error. I am on newest firmware (540). Reboot and factory reset doesn't help. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted February 6 Administrators Share Posted February 6 Are you able to access via a PC instead of the app/mobile web browser? Did you factory reset after installing initially? How have you done a factory reset exactly? Link to comment Share on other sites More sharing options...
BlackBoXBoSS Posted February 6 Author Share Posted February 6 I am not able to access via PC or mobile. I did factory reset after upgrading to newest firmware. I did factory reset from the recovery options and manually with reset button. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted February 6 Administrators Share Posted February 6 Delete the downloaded firmware from your PC, re-download it from the topic and then from the recovery options, re-upgrade to the same firmware version, close the tab, wait 4 minutes then access again, does it work then? Link to comment Share on other sites More sharing options...
BlackBoXBoSS Posted February 6 Author Share Posted February 6 Still doesn't work. When I click continue anyway I get this. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted February 6 Administrators Share Posted February 6 In settings grab the logs from the troubleshooting > advanced page please and attach it here. Also disable BI in troubleshooting settings, reboot from the interface, wait 4 minutes then access and see if it loads better please Link to comment Share on other sites More sharing options...
BlackBoXBoSS Posted February 6 Author Share Posted February 6 Here are the logs. I disabled BI. R3_2025-02-06T17_15_03.750Z_logs.txt Link to comment Share on other sites More sharing options...
BlackBoXBoSS Posted February 6 Author Share Posted February 6 After disabling BI and reboot I got this. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted February 6 Administrators Share Posted February 6 Use the recovery to downgrade back to the previous version please, are you able to get it stable then? Link to comment Share on other sites More sharing options...
BlackBoXBoSS Posted February 6 Author Share Posted February 6 I was getting this error on previous version as well. When I reboot R3 it let me access interface once or a few times and then it is back to giving error every time. It has been like that for a couple of firmwares now and I have no idea how to fix it. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted February 6 Administrators Share Posted February 6 When you upgrade are you usually using the in built way to do so or doing it manually? Link to comment Share on other sites More sharing options...
BlackBoXBoSS Posted February 6 Author Share Posted February 6 I always update manually. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted February 6 Administrators Share Posted February 6 Okay so make sure you're on the previous version then allow the router to upgrade you instead and see if you get the same issue please Link to comment Share on other sites More sharing options...
BlackBoXBoSS Posted February 6 Author Share Posted February 6 Still getting failed to load minimum required components. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted February 6 Administrators Share Posted February 6 If your ISP modem/router has WiFi, set it up so that it is in bridge or modem mode, you can also use the DMZ. Copy the WAN IP from the R3 (found in Settings > WAN) and enter it into the DMZ function on the ISP modem/router. Disable IPv6 in LAN/WAN on the R3 and enable remote support in Settings > Troubleshooting. Then post back here from a device connected to the R3 when you've done that and I'll try to get a dev to have a look tomorrow. If you're able to make it load to enable remote support or in the recovery options that is. It doesn't look like you have IPv6 either if you're posting from a device connected to the router so you can ignore that. Also the WAN IP is also the same IP you would see the ISP modem/router give it on its interface. Link to comment Share on other sites More sharing options...
BlackBoXBoSS Posted February 6 Author Share Posted February 6 I did factory reset once again and disabled WAN/LAN IPv6 and it is loading correctly for now. I enabled remote support if a dev want to take a look. Link to comment Share on other sites More sharing options...
Administrators Netduma Fraser Posted February 6 Administrators Share Posted February 6 If it's working for now there won't be anything for them to look at but glad to hear it's working, let us know if it happens again Link to comment Share on other sites More sharing options...
BlackBoXBoSS Posted February 6 Author Share Posted February 6 I believe the issue was IPv6, so maybe it could get fixed with a new firmware. Thanks for help! Netduma Fraser 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now