jose13lilt

Hi, the geo-filter doesn't work in warzone 2.0, when it's active it keeps looking for a lobby permanently

smb data transfer with the xr1000 is +-100MB/s over wifi or wired

perfect. Is there a beta tester version of the next version to test it and report the result?

I don't think it's a hardware limitation, because a $7 router works perfectly, and the xr500 in ap mode smb works fine, it's in router mode that it doesn't work correctly

with the xr1000 it works perfectly, both wired - wired, wired - wifi, wifi - wifi communication. I think that the problem may be the firmware, since the xr1000 has a different version than the xr500, I am working with the version: XR1000 1.0.0.52_1.0.38

good morning, today I'm going to do the test with the XR1000

I'm sorry, I can do the tests for a week, now I'm on holidays

smartconnect was disabled, I also tried disabling coexistence

in AP MODE it works fine, but I want to replace the ISP router (it is valued at 7$)

the ascending modem (ISP router) is Arcadyan PRV3399B-B-LT I explain how I have the network set up: Arcadyan PRV3399B-B-LT to Fiber Optic ONT (wifi disabled, only one LAN port occupied by XR500) XR500 (AP mode) to Arcadyan PRV3399B-B-LT small devices via RJ45 CAT-5e to a 1Gb switch on each connector switch by RJ45 CAT- 8 to XR500 SMB server by RJ45 CAT-8 to XR500 2.4G wifi devices to XR500 5G wifi devices to XR500 (I had previously mounted this same network only with Arcadyan PRV3399B-B-LT) I wanted to replace the router with the XR500 because it was more powerful. I replaced the router with the XR500 and had the problem that I have mentioned, so I did the following test: XR500 router mode: (only 3 devices on the network) XR500 to ONT Fiber Optic SMB server by RJ45 CAT-8 to XR500 PC by RJ45 CAT-8 to XR500 Lapptop by wifi 5G to XR500 Wired PC connection to SMB server Works fine Laptop connection by wifi 5G to SMB server Does not work well laptop connection by wifi 2,4G to SMB server not working well connection with another different laptop by 5G Wi-Fi to SMB server does not work well connection with a different laptop by wifi 2.4G to SMB server does not work well

SMB is connected to the XR500 in AP MODE

in AP mode it works fine, in router mode with QoS disabled it doesn't,

All this is with router mode configured with ONT WAN connection, now I am testing with Access Point, and it seems to work better, but my intention is to remove the ISP Router, and use my XR500 as a network router.

It is impossible to transfer SMB via Wi-Fi, apart from being slow it is super unstable, it loses connection with the SMB device, by cable it works perfectly, but via Wi-Fi, when trying to read the folder it takes a long time and even loses the connection, if you try to transfer it can't do it, it stays calculating and then loses the connection. but this router (Arcadyan PRV3399B-B-LT) can be found for €7 on the internet, it is the one provided by the ISP here in Spain, and with it the SMB works perfectly both by wifi and by cable, Is it possible that the failure is due to a bad system optimization that separates the wired LAN network from the wireless LAN and has problems interacting between these interfaces?

FTP works fine, but it doesn't work for me, I need SMB yes or yes, but SMB is extremely slow, to read what is inside a folder it takes several minutes, I don't know why it is so slow, but with an ISP router it works perfectly . Today I was testing, if the SMB is mounted on the wired network, and another computer is wired, it works fine, but if the SMB is mounted by cable, and you try to access it from a laptop via wifi, it is when it is extremely slow, the internet connection via wifi shows me that it is high, then I do not understand what happens.