Jump to content
VVarrior

my gui on xr1000 is so slow

Recommended Posts

There were fixes that were added that should already be apart of the version. What device/web browser are you using? How slow is it exactly, whats the average time to load a page? Clear the browser cache/cookies then load each page once and it should be faster after that.

Share this post


Link to post
Share on other sites
8 hours ago, Netduma Fraser said:

There were fixes that were added that should already be apart of the version. What device/web browser are you using? How slow is it exactly, whats the average time to load a page? Clear the browser cache/cookies then load each page once and it should be faster after that.

Am currently using google chrome and opera for the browser.

Average time to load is like a 1minute 

Going to clear cache/cookies 

Also once a while my devices disconnect and upnp does not work  any fix to this 

Share this post


Link to post
Share on other sites
20 minutes ago, Netduma Fraser said:

Keep us updated on the speed. How often does that occur? That's likely related to DHCP and setting reserved IPs for the devices should help keep that to a minimum.

After clearing the caches/cookies now it takes 30 seconds cut the time in half 

it occurs in the morning most likely they just randomly disconnect should i give my devices a static ip ? and manual portforward?

Share this post


Link to post
Share on other sites

Try accessing the interface using this link: 

http://192.168.1.1

is it any faster? Yes in LAN Settings on the router give devices a static/reserved IP. Should be quite easy, click on the table and click apply to give them the same details they already use. No need to use port forwarding.

Share this post


Link to post
Share on other sites
7 hours ago, Netduma Fraser said:

Try accessing the interface using this link: 

http://192.168.1.1

is it any faster? Yes in LAN Settings on the router give devices a static/reserved IP. Should be quite easy, click on the table and click apply to give them the same details they already use. No need to use port forwarding.

i tried that link but didn't work my gateway is a 192.168.1.254 so it would in interfere with my gateway so i had to change it to 10.0.0.1 

just gave a static ip all let you know in the morning see is the devices are still online 

and as for upnp sometimes it works sometimes it doesn't 

is there a new firmware for xr1000 i can try ??

Share this post


Link to post
Share on other sites
7 hours ago, VVarrior said:

i tried that link but didn't work my gateway is a 192.168.1.254 so it would in interfere with my gateway so i had to change it to 10.0.0.1 

just gave a static ip all let you know in the morning see is the devices are still online 

and as for upnp sometimes it works sometimes it doesn't 

is there a new firmware for xr1000 i can try ??

OK, so does navigating to 10.0.0.1 load any quicker than routerlogin.net?

Let us know if connections are still dropped.

What firmware are you currently running? 

Share this post


Link to post
Share on other sites
6 hours ago, Netduma Liam said:

OK, so does navigating to 10.0.0.1 load any quicker than routerlogin.net?

Let us know if connections are still dropped.

What firmware are you currently running? 

Update on xr1000 now my gui is not loading unless i restart it the router 

everything still connected at the moment after a day 

the firmware am on is 1.0.0.52 Xr1000  any newer firmware available i can try to fix this problem??

Share this post


Link to post
Share on other sites
16 hours ago, VVarrior said:

Update on xr1000 now my gui is not loading unless i restart it the router 

everything still connected at the moment after a day 

the firmware am on is 1.0.0.52 Xr1000  any newer firmware available i can try to fix this problem??

Did you do a factory reset after installing the upgrade? This is recommended as it clear any low-level coder left after the last firmware. 

Share this post


Link to post
Share on other sites
7 hours ago, Netduma Liam said:

Did you do a factory reset after installing the upgrade? This is recommended as it clear any low-level coder left after the last firmware. 

Yes factory reset it after the upgrade 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...